12v240wpsu-1
12v 240W PSU

12v 240W 20A power supply Brand new in box, high quality power supply. AC input voltage selector switch, select either 110v or 240v. This PSU is meant for internal use. The buyer is responsible for ensuring safety of the installation.

not rated $18.58Add to basket
19v-120w-psu
19v 120W power supply

Fisher Delta 3D printer power supply, suitable for running a heated print surface. To upgrade your Fisher, please see our heatbed upgrade bundle here. Power supply specification: 19v, 6.32A, 120W, 5.5*2.5 connector.  

not rated $31.04Add to basket
fan_12v
40x40x10mm fan

Select 19v for use in Fisher, the Huxley hot end, or as a part cooling fan for a Huxley 3D printer. Select 12v for use in the Mendel hot end, Ormerod hot end or as a part cooling fan for a Mendel or Ormerod 3D … Read More

not rated $2.49Select options
597-1-5v-regulator-PCB
5v Regulator PCB

The 5V regulator replaces the Duet’s on-board 5V buck converter.  Making this replacement reduces electronic noise and allows the wiring in all RepRapPro’s 3D printers to be routed correctly. Includes extra screw terminal for distributing power to the Duet Shield … Read More

not rated $6.23Read more
axial-fan-50mm
Axial fan 50mm

50mm Axial (blower) fan. Runs at 19v. Suitable for Fisher and Huxley 3D printers.

not rated $4.92Add to basket
thermistor_100k
Axial thermistor 100k

DO-35 style axial thermistor suitable for all RepRapPro hot ends. The thermistor comes with a length of PTFE heatshrink.

not rated $3.68Add to basket
cartridge-heater-19v
Cartridge heater

Cartridge heater, available for use at 19v (yellow leads) or 12v (red leads). Length: 15mm Diameter: 5mm Wire length: 160mm Please note: the 19v cartridge heaters are now supplied with yellow leads and replace the heaters with white leads, to … Read More

not rated $6.23Select options
duet_big
Duet PCB

The Duet is an open-source 3D printer controller board, which offers a range of improvements over traditional 8-bit AVR based control boards. Features Hardware: 32 bit ARM microprocessor as found on the Arduino Due, running at up to 84MHz 12-35v … Read More

5 out of 5
$92.26Add to basket
duet-shield
Duet Shield PCB

The Duet Shield PCB adds the capability of driving up to two more extruders for three feed machines. The board has been designed to neatly fit over the Duet and it has horizontal connectors to give it a low profile … Read More

not rated $36.15Add to basket
fisher-microswitch
Endstop microswitch

Short lever microswitch for use with Fisher Delta 3D printer. This microswitch is also suitable for use as an endstop on Mendel, Ormerod and Huxley 3D printers.

not rated $1.25Add to basket
831-SP200-PSUa
Meanwell 12v PSU

As used on the RepRapPro Ormerod 2 3D printer. This power supply features auto input voltage switching for AC 110v or 240v operation, and is extremely robust. It will happily power a 200x200mm (8″x8″) heated bed, as well as NEMA17 … Read More

not rated $24.81Add to basket
meltzi
Melzi PCB v2

Genuine RepRapPro Melzi v2 RepRap electronics board, with A4982 stepper drivers, high current screw terminal for power and heated bed, as well as 2oz copper pour for adequate heat sinking of the stepper driver chips. Processor: ATMega1284P Axes: 4 x … Read More

not rated $80.91Read more