Remove the protective film from the acrylic panel.
The microswitches fit to the inside of the panel. Note the orientation of the bottom of the panel; this fits around the Duet electronics.
Fit the microswitches with cable ties, as you did with the first microswitch. Make sure the cable tie end is towards the top of the panel.
The endstop looms have two wire, and there are three different lengths.
The hot end loom has eight wires.
The extruder motor wire has four wires.
Mount the shortest endstop loom, the hot end loom and the extruder motor loom on the left side. The other two endstop looms go on the right.
Left side: Attach the endstop loom to the microswitch on the left hand side. Put the crimps on the outside tabs of the microswitch, NOT the middle one. Polarity is not important. Try not to bend the crimps on the microswitch tabs, or they will become loose.
Fasten the endstop loom in the top cable tie, the endstop and the extruder loom in the next one down, and all three looms in the rest of the cable ties. Don’t fully tighten the cable ties yet, so you can adjust the wire position.
Right side: connect the shorter endstop loom to the microswitch.
Cable tie both wires in all of the positions.
Attach the extuder to the panel, with two M3x12mm cap head screws, from the outside. Connect the extruder motor loom to the extruder motor.
Fit the panel and connect
As with the other panels, lift the printer up off the surface, and fit the top of the panel onto the screws in the idler printed part.
Line up the bottom with the holes in the motor mounts, and fasten with four M3x16mm cap head screws. Make sure the wiring looms fit into the slots in the base plate.
Connect the Bowden tube to the extruder. Simply push the bowden tube into the pneumatic fitting.
Connect the third microswitch in the same way as the other two, and cable tie it to the panel.
Connect the hot end loom to the hot end. We find it useful to cable tie the loom loosely to the Bowden tube, above and below the connector.
Now adjust the cable lengths until everything is neat. The hot end loom and Bowden tube should move together. Try and get a nice loop, so they concertina up as the effector moves up.
Tighten and trim all of the cable ties. Move the carriages up and down their full range of movement, making sure they don’t catch on anything. Check that the heads of the cable ties don’t get in the way, and that the wiring looms are neat against the side panels. Adjust any cables as needed, and make sure the hot end loom and Bowden tube don’t catch on anything.
Bed probe wiring
You will need the following parts:
#
Component
Qty
Type
1203
Bed probe loom
1
Wiring
1202
Bed probe wire
2
Wiring
M3x12mm cap head screw
6
Fastener
212
M3 washer
6
Fastener
1253
M3x8mm spacer
6
Hardware
Fit the bed probe loom 3-way connector to the E-stop header on the Duet. Push the wires through the slots in the base, as shown. The long wire can go under the Duet, if you prefer.
Attach the ring terminals of the bed probe loom and bed probe wires to the bed mounting brackets. For each connection, the order is M3x12mm cap head screw, ring terminal of loom, bed mounting bracket, M3 washer, round spacer.
View from the front of the bed mounting bracket.
Repeat the above steps for all six connections. The circuit goes around the circle. The balls on the print surface will complete the circuit (see later). When the nozzle pushes down on the bed, the circuit is broken. This calibrates the nozzle height.
Fit the power jack
You will need the following parts:
#
Component
Qty
Type
193
Power jack
1
Electronics
455
Power jack nut
1
Electronics
Turn the printer over. It can rest on it’s top as you connect the wiring. The DC power jack may now be fitted as shown, next to the ethernet socket.
Duet connections
Wiring diagram
The instructions below show the fitting of the wiring. If in doubt, refer to this wiring diagram.
Duet wiring connections
Connect the wiring looms to the Duet, as shown in the pictures below (click on any picture for a larger version). Also refer to the wiring diagram, above. You will need the following parts:
#
Component
Qty
Type
1201
DC cable – 250mm
1
Wiring
477
Motor loom – 160mm
1
Wiring
478
Motor loom – 90mm
2
Wiring
FAN0 – NO CONNECTION! Do not connect anything to the first two pins on the left. They are not used on the Fisher.
E0_TEMP – Hot end thermistor (green/blue, 2-way)
E0_HEATER – Hot end heater (black/purple/red/brown, 4-way)
– Hot end fan (yellow/none/white, 3-way)
NOTE: this connects to the double row of pins, NOT to ‘FAN0’. From the left, there should be two clear pins, then the yellow wire, another pin (covered by the housing, but not connected), then the white wire.
E0_MOT/STOP – (on first three pins) Bed probe (red/blank/red, 3-way). This was already fitted in the bed probe wiring step.
E0_MOT/STOP – (on the other four pins) Extruder drive motor (yellow/green/blue/red, 4-way)
X_MOT/STOP – X endstop (blue, space, red, 3-way) This is the SHORTEST endstop loom.
X_MOT/STOP – (on the other four pins) X motor (black/green/blue/red, 4-way)
Now connect the X motor to the Duet, using a 90mm motor loom. This is the motor closest to the motor connection pins on the Duet. Check that the endstop at the top of this tower is the one connected next to the X motor.
Y_MOT/STOP – Y endstop (blue, space, red, 3-way) This is the LONGEST endstop loom.
Y_MOT/STOP – (on the other four pins) Y motor (black/green/blue/red, 4-way)
Next the Y motor, using a 90mm motor loom. This is the motor nearest the large screw terminals on the end of the Duet board. Check that the endstop at the top of this tower is the one connected next to the Y motor.
Z_MOT/STOP – Z endstop (blue, space, red, 3-way) This is the MEDIUM length endstop loom.
Z_MOT/STOP – (on the other four pins) Z motor (black/green/blue/red, 4-way)
Now the Z motor, using the 160mm motor loom. This is the motor nearest the ethernet socket on the Duet. Check that the endstop at the top of this tower is the one connected next to the Z motor.
All the wiring connections fitted.
This picture shows the motor connections, and orientation. If you have put the motor on the wrong way around, you can turn the motor around, to make the motor wiring easier. Unscrew the four motor screws, and turn the motor around, then retighten the screws.
Finally, connect the DC power cable. One of the cores has a black stripe running along it’s length. Connect this to the negative terminal (on the left hand side as viewed in the photograph).
Connect the DC power cable to the tabs on the back of the jack.
Ground is the centre of the three tabs (the wire with the black stripe should connect to this), and positive is the tab that connects to the centre pin. Fit them with the ‘curly’ part of the crimp outwards.
With all the wiring fitted, tidy up the wiring so that it all fits below the level of the acrylic side panels. You can use a couple of cable ties to help.
Jumper
You will need the following parts:
#
Component
Qty
Type
Fisher
1
Part-assembled
285
PCB Jumper
1
Electronics
Fit the jumper onto the 5V_EN (JP9) header pins (location highlighted in the picture). This uses the on-board 5V regulator to supply power to the main processor of the Duet, when 19V power is connected.
